6b attach
Northwest Ports Clean Air Strategy 2013 Update | December 2013 ACKNOWLEDGMENTS The Port of Seattle, Port of Tacoma, and Port Metro Vancouver jointly developed the Northwest Ports Clean Air Strategy2013 Update with contributions from partner agencies. The ports would like to thank the following organizations for their contributions: For collaboration on Strategy development and implementation: Environment Canada Metro Vancouver Puget Sound Clean Air Agency United States Environmental Protection Agency Washington State Department of Ecology For facilitation and drafting: SLR International Corporation Cascadia Consulting Group, Inc. Stephanie Jones Stebbins Jason Jordan Ronan Chester 206.787.3818 253.830.5321 604.665.9311 jonesstebbins.s@portseattle.org jjordan@portoftacoma.com ronan.chester@portmetrovancouver.com www.portseattle.org www.portoftacoma.com www.portmetrovancouver.com Richard Holt Dan Brown Frank Van Haren 604.666.6552 503.326.6832 360.407.6870 richard.holt@ec.gc.ca brown.dan@epa.gov fvan461@ecy.wa.gov www.ec.gc.ca www.epa.gov www.ecy.wa.gov Shelina Sidi Andrew Green 604.436.6750 206.689.4053 shelina.sidi@metrovancouver.org andrewg@pscleanair.org www.metrovancouver.org www.pscleanair.org Northwest Ports Clean Air Strategy Update 2013 ii CONTENTS Acknowledgments ........................................................................................................................ii Executive Summary ......................................................................................................................1 Strategy Overview ........................................................................................................................5 Airshed Emission-Reduction Goals ..............................................................................................8 Performance Targets by Sector ..................................................................................................10 1. Ocean-Going Vessels .......................................................................................................12 2. Harbor Vessels .................................................................................................................15 3. Cargo-Handling Equipment ..............................................................................................17 4. Trucks ...............................................................................................................................19 5. Locomotives and Rail Transport .......................................................................................21 6. Port Administration ...........................................................................................................23 Pilot Studies and Demonstration Projects ..................................................................................25 Performance Reporting ..............................................................................................................27 Conclusions and Next Steps ......................................................................................................28 Glossary .....................................................................................................................................29 Appendix A. Port Emissions Inventories .....................................................................................33 Appendix B. Air Emission Regulations in U.S. and Canada .......................................................38 Appendix C. Summary of Public Comments ..............................................................................42 Tables Table 1. Summary of Actions and Performance Targets by Sector for 2015 and 2020 ................2 Table 2. Emission-Reduction Goals for DPM and GHGs by 2015 and 2020 ...............................9 Table 3. Actions and Performance Targets for Ocean-Going Vessels ........................................14 Table 4. Actions and Performance Targets for Harbor Vessels ..................................................16 Table 5. Actions and Performance Targets for Cargo-Handling Equipment ...............................18 Table 6. Actions and Performance Targets for Trucks ................................................................20 Table 7. Actions and Performance Targets for Locomotives and Rail Transport ........................22 Table 8. Actions and Performance Targets for Port Administration .............................................24 Table A-1. Port of Seattle2011 Emissions Inventory for Puget Sound Airshed .......................34 Table A-2. Port of SeattleChanges in Port Airshed Emissions from 2005 to 2011 ..................34 Table A-3. Port of Tacoma2011 Emissions Inventory for Puget Sound Airshed ......................35 Table A-4. Port of TacomaChanges in Port Airshed Emissions from 2005 to 2011 .................35 Table A-5. Port Metro Vancouver2010 Emissions Estimates for Lower Fraser Valley Airshed ...37 Table B-1. Comparison of Air Emission Regulations in the United States and Canada .............38 Figures Figure 1. Georgia Basin-Puget Sound Airshed Boundaries ..........................................................6 Figure 2. Port-Related DPM and GHG Emissions by Sector from the Three Ports, 20102011 ......11 Figure A-1. Puget Sound Maritime Emissions Inventory Boundaries ..........................................33 Figure A-2. Port Metro VancouverEmissions Inventory Boundaries ........................................36 Northwest Ports Clean Air Strategy Update 2013 iii This page intentionally left blank. Northwest Ports Clean Air Strategy Update 2013 iv EXECUTIVE SUMMARY The Port of Seattle, Port of Tacoma, and Port Metro Vancouver are continuing their collaborative efforts on the Northwest Ports Clean Air Strategy to reduce emissions from shipping and port operations in the Georgia BasinPuget Sound airshed. In developing and implementing the 2007 Strategy and this 2013 Strategy Update, the three ports partnered with government agencies, including Environment Canada and Metro Vancouver in Canada and the U.S. Environmental Protection Agency, Washington State Department of Ecology, and Puget Sound Clean Air Agency in the United States. Collectively, the three ports and ve government agencies are referred to as the Strategy partners. The voluntary actions in this Strategy Update are intended to complement regulations and, together with the regulations, achieve the following emission reductions relative to a 2005 baseline: Reduce diesel particulate matter (DPM) emissions per ton of cargo by 75% by 2015 and 80% by 2020, to decrease immediate and long-term health effects on adjacent communities. Reduce greenhouse gas (GHG) emissions per ton of cargo by 10% by 2015 and 15% by 2020, to limit contributions to climate change and reduce associated environmental, health, and economic impacts. These goals account for changing levels of port activity and focus on increasing efciency per ton of cargo moved through the ports. Unless otherwise noted, the Strategy partners intend to meet targets by the end of the stated calendar yearthat is, the 2015 targets will be achieved by December 31, 2015. Since adopting the rst Strategy in 2007, the Strategy partners have evaluated data and lessons learned from implementation efforts, advances in emission-reduction technology, and changes in the regulatory landscape. This experience to date informs the Strategy Update and its key elements: Goals for reducing port-related emissions in the Georgia BasinPuget Sound airshed. Performance targets for 2015 and 2020 for reducing emissions in each covered sector. Pilot studies and demonstration projects to assess how new emission-reduction technologies can help meet the emission-reduction goals. The ports developed inventories of port-related air emissions in 2005 and updated their emissions inventories in 2010 and 2011. The updated inventories show considerable progress in reducing emissions since 2005, and they provide data to identify areas for continued improvement going forward. The emissions inventories and the Strategy Update cover the following sectors of port-related operations: 1. Ocean-going vessels 2. Harbor vessels 3. Cargo-handling equipment Northwest Ports Clean Air Strategy Update 2013 1 4. Trucks 5. Locomotives and rail transport 6. Port administration Table 1 summarizes the actions and performance targets in each sector of the Strategy Update as presented in later chapters. Together, these performance targets are designed to achieve the airshed emission-reduction goals for 2015 and 2020. The Strategy partners also committed to conducting pilot studies and demonstration projects to advance innovative approaches to reduce emissions from these sectors. Table 1. Summary of Actions and Performance Targets by Sector for 2015 and 2020 Reduces Sectors and Actions 2015 Targets 2020 Targets DPM GHG Ocean-Going Vessels OGV-1 Vessels surpass Emission Control Area (ECA) Early compliance Ports track requirements with 2015 ECA number of 0.1% fuel- vessels with Tier sulfur level (or 3 marine engines, equivalent) while shore power use, hotelling before cleaner fuel, or 2015 other emissionreduction technologies OGV-2 Ports and vessels participate in port-designed Ports and 10% of Ports and 40% of or third-party certication programs that vessel calls vessel calls promote continuous improvement (such as Environmental Ship Index, Green Marine, Clean Cargo Working Group, or others) Harbor Vessels Harbor-1 Strategy partners conduct annual outreach Partners conduct Partners conduct to port-related harbor vessel companies outreach and 50% outreach and 90% and recognize best practices and engine of harbor vessel of harbor vessel upgrades companies report companies report best practices and best practices and engine upgrades engine upgrades Harbor-2 Ports and harbor vessels participate in port- Ports and 10% of Ports and 40% of designed or third-party certication programs harbor vessels harbor vessels that promote continuous improvement (such as Environmental Ship Index, Green Marine, Clean Cargo Working Group, or others) Continued > Northwest Ports Clean Air Strategy Update 2013 2 Table 1. Summary of Actions and Performance Targets by Sector for 2015 and 2020 (continued) Reduces Sectors and Actions 2015 Targets 2020 Targets DPM GHG Cargo-Handling Equipment CHE-1 CHE meets Tier 4 interim (T4i) emission 50% of 80% of standards or equivalent equipment equipment CHE-2 Ports and terminals have fuel-efciency plans Ports and 50% of Ports and 100% in place that promote continuous improvement terminals of terminals Trucks Truck-1 Trucks meet or surpass U.S. EPA emission 100% of trucks by the end of 2017 standards or equivalent for model year 2007 Truck-2 Ports, terminals, and trucks have fuel- Ports Ports, terminals, efciency plans in place that promote and 50% of continuous improvement trucks Locomotives Rail-1 Switcher locomotive owners/operators 100% of owners/ 100% of owners/ participate in a fuel-efciency program operators operators institute a achieve program performance objectives of chosen program Rail-2 Switcher locomotive owners/operators 10% of 20% of upgrade or replace unregulated engines unregulated unregulated (engine replacements will be Tier 2 or better) locomotive locomotive engines engines Continued > Northwest Ports Clean Air Strategy Update 2013 3 Table 1. Summary of Actions and Performance Targets by Sector for 2015 and 2020 (continued) Reduces Sectors and Actions 2015 Targets 2020 Targets DPM GHG Port Administration Admin-1 Ports own and operate cleaner vehicles and Ports report Ports increase equipment and have fuel-efciency plans in use of cleaner use of cleaner place that promote continuous improvement vehicles and vehicles and equipment and equipment other relevant information Admin-2 Ports apply clean construction standards to Ports adopt Ports continue engines used on port-led construction projects clean to apply clean (such as American Association of Port Authorities' construction construction Sustainability Checklist, U.S. EPA Best Practices practices for practices for for Clean Diesel Construction, or equivalent best port-led projects, port-led projects, management practices) including idle- including idlereduction reduction requirements, requirements, and enact a plan and enact a plan to address Tier 2 to address Tier 4 engine emission engine emission requirements requirements Admin-3 Ports facilitate energy studies and Each port Each port conservation projects at port-operated and/or conducts 3 completes tenant facilities to identify and address energy energy studies 3 energy conservation opportunities in building systems, conservation operations, and yard lighting projects Northwest Ports Clean Air Strategy Update 2013 4 STRATEGY OVERVIEW The Port of Seattle, Port of Tacoma, and Port Metro Vancouver are continuing their collaborative efforts on the Northwest Ports Clean Air Strategy to reduce maritime and port-related emissions from global marine trade and port operations in the Georgia BasinPuget Sound airshed (see Figure 1). In developing and implementing the 2007 Strategy and this 2013 Strategy Update, the three ports partnered with government agencies, including Environment Canada and Metro Vancouver in Canada and the U.S. Environmental Protection Agency, Washington State Department of Ecology, and Puget Sound Clean Air Agency in the United States. Together, the three ports and ve agencies constitute the Strategy partners.1 Ports are a critical part of the Pacic Northwest and North American economy, facilitating movement of people and goods and supporting living-wage jobs. With their tenants and customers, the three ports use diesel-powered ships, trains, trucks, and other equipment to move goods and passengers through the ports to other destinations.2 The Strategy creates a harmonized approach to improving air quality and reducing port-related emissions in the shared airshed to safeguard public health and the environment while supporting economic growth. The 2007 Strategy and this 2013 Strategy Update contain shared emission-reduction goals and targets for the three ports, with exibility for how each port meets the targets through actions appropriate to its particular situation. The Strategy Update incorporates new emissions inventory data, regulatory changes, and emerging issues to set performance targets for 2015 and 2020. These targets build on previous actions and take additional steps to reduce emissions. Unless otherwise noted, the Strategy partners intend to meet targets by the end of the stated calendar yearthat is, the 2015 targets will be achieved by December 31, 2015. To reduce emissions in advance of and complementary to regulations, the Strategy Update focuses on voluntary actions to address three primary objectives: 1. Reduce port-related air quality impacts from diesel particulate matter (DPM) emissions to decrease immediate and long-term health effects on human health, the economy, and the environment in the airshed. 2. Reduce greenhouse gas (GHG) emissions to limit contributions to climate change and reduce associated environmental, health, and economic impacts. 3. Help meet air quality standards and objectives for the airshed. The Strategy's success relies on signicant contributions from port tenants, customers, and other stakeholders who manage port activities and equipment that produce air emissions, as well as regional transportation agencies that can inuence freight movement. With their tenants and stakeholders, the three ports seek to manage future growth in a way that improves air quality and supports sustainable port operations. 1 The British Columbia Ministry of Environment and the American Recovery and Reinvestment Act provided additional technical and nancial support toward emission-reduction initiatives related to the Northwest Ports Clean Air Strategy. 2 The Strategy Update uses "diesel" as a concise reference for fuel oils, including diesel, bunker fuel, and other heavy crude fuels. Northwest Ports Clean Air Strategy Update 2013 5 Targeted Emissions and Inventories The Strategy Update focuses on voluntary actions to reduce emissions of DPM and GHGs. Such actions often yield related benets of decreasing other air pollutants, such as sulfur and nitrogen oxides, carbon monoxide, volatile organic compounds, and air toxics. Reducing DPM also reduces black carbon emissions, which contribute to climate change, though black carbon reductions are not quantied in this Strategy Update. Air emissions inventories covering Port Metro Vancouver were completed in 2010 (Landside Emissions Inventory and National Marine Emissions Inventory for Canada), and the ports of Seattle and Tacoma updated their emissions data in 2011 (as part of the Puget Sound Maritime Air Emissions Inventory).3 The updated inventories show considerable progress in reducing emissions since the previous 2005 inventories; they also highlight areas for continued improvement, which this Strategy Update addresses. Appendix A provides more information on the inventories, and Appendix B compares air emission regulations in the United States and Canada. Geographic Scope Figure 1. Georgia Basin-Puget Sound Airshed Boundaries The Port of Seattle, Port of Tacoma, and Port Metro Vancouver share a Canada common airshed. This joint Strategy Georgia Detailed Area seeks to improve air quality around Basin U.S.A. the three largest ports and maritime Whistler industry hubs in the Northwest, with Campbell River Powell River benets that extend throughout the Squamish Courtenay Georgia BasinPuget Sound airshed (see Figure 1). The airshed centers St Hope rait o f G Vancouver Nanaimo e or g i a on the marine area known as the Salish Sea and includes the Strait of Bellingham Juan de Fuca, greater Puget Sound area, Strait of Georgia, Haro Strait, S t Victoria r a i t o f J Boundary Pass, Rosario Strait, and u a n d e F u ca Puget other nearby waterways. Port Sound Angeles Emissions inventory boundaries Seattle are delineated in the 2010 and 2011 inventories, as described in Appendix Tacoma Port Authority A. These reports estimate the Airshed Olympia International Boundary quantity of emissions from maritimerelated activities within the shared 0 15 30 45 60 Kilometers I 0 10 20 30 40 Miles airshed. The emissions inventories for Port Metro Vancouver and Puget Sound (including the Port of Seattle and Port of Tacoma) were conducted independently and use different boundary delineations. 3 Starcrest Consulting Group, LLC, 2011 Puget Sound Maritime Air Emissions Inventory, May 2013 update; SNC-Lavalin, Port Metro Vancouver 2010 Landside Emissions Inventory, March 26, 2012; SNC-Lavalin, 2010 National Marine Emissions Inventory for Canada, March 31, 2012 (not yet published; available by request from Environment Canada). Region 2 in Environment Canada's 2010 national inventory covers Port Metro Vancouver's jurisdictional area. Northwest Ports Clean Air Strategy Update 2013 6 Strategy Update Contents The Strategy partners worked together to review their emissions inventories and to develop shared emission-reduction goals and performance targets by sector. In June 2013, the partners released a draft of this Strategy Update for public review and comment. Outreach was conducted, and public open houses were held to solicit comments. Comments were accepted at the open houses, in person, by mail, and online through July 31, 2013, for the ports of Seattle and Tacoma and through August 9 for Port Metro Vancouver. The three ports received comments from 45 respondents; Appendix C provides a summary of the public comments received. The partners reviewed all comments received and revised the Strategy Update. The remainder of this Strategy Update includes the following chapters: Airshed Emission-Reduction Goals. The Strategy Update contains airshed-wide goals for reducing port-related DPM and GHG emissions. To develop these goals, the Strategy partners considered data collected through implementation since 2007, advances in emission-reduction technology, actions taken, and changes in the regulatory landscape. Performance Targets by Sector. The Strategy partners updated the previous 2015 performance measures (now called performance targets) and set new performance targets for 2020. The Strategy Update includes new and updated actions and performance targets for the following sectors: 1. Ocean-going vessels 2. Harbor vessels 3. Cargo-handling equipment 4. Trucks 5. Locomotives and rail transport 6. Port administration Pilot Studies and Demonstration Projects. The Strategy Update calls for pilot studies and demonstration projects designed to advance emission-reduction technologies for the maritime and port industry. Performance Reporting. Each year, the Strategy partners publish an implementation report that summarizes emission-reduction activities and tracks progress on performance targets. The annual report presents progress and compares results with previous years. Every ve years, the ports will update their air emissions inventories and analyze progress toward emission-reduction goals. Following the Conclusions and Next Steps chapter, a Glossary provides explanations of terms and abbreviations used in the Strategy Update. Appendix A includes more information on the port emissions inventories, and Appendix B provides a comparison table of relevant air emission regulations in the United States and Canada. Appendix C summarizes comments received during the public review period. Northwest Ports Clean Air Strategy Update 2013 7 AIRSHED EMISSION-REDUCTION GOALS This Strategy Update is designed to reduce emissions at the three ports as well as to complement and expand on regulatory requirementsby adopting measures early, achieving higher levels of emission reductions, and taking other voluntary steps to reduce emissions. The three ports established emission-reduction goals that reect their commitment to improving the environment while fostering economic growth. The voluntary actions in the Strategy Update are intended to complement regulations and, together with the regulations, achieve the following emission reductions relative to the 2005 baseline emissions inventories: Reduce DPM emissions per ton of cargo by 75% by 2015 and 80% by 2020. Reduce GHG emissions per ton of cargo by 10% by 2015 and 15% by 2020.4 These goals account for changing levels of port activity and focus on increasing efciency per ton of cargo moved through the ports. The partners chose to set goals per ton of cargo throughput for consistency, recognizing that the ports have different growth projections. While supply-chain efciency can reduce emissions per ton of cargo, it is the total emissions of DPM and GHGs that affect overall air quality in the region and contribute to climate change. For total DPM emissions, technology advancements and regulatory requirements are expected to reduce the total DPM output, even as cargo throughput increases. In addition to expected DPM reductions due to phase-in of regulations and anticipated turnover of eet vehicles and equipment, the Strategy partners will continue to seek additional reductions across all sectors. The three ports estimate that their total DPM emissions will be reduced by 70% by 2015 and 75% by 2020, relative to the 2005 baseline. Reduced diesel emissions will also decrease the associated immediate and long-term health effects on adjacent communities. Total GHG emissions from the three ports combined are not currently anticipated to decrease over the 20152020 period due to expected port growth. Most GHG emissions from the ports are directly tied to fuel consumption. As a result, they tend to increase with growth in port operations, although efciency gains can help offset increases. The Strategy partners recognize that, by 2015, work is needed both to implement projects that will reduce GHG emissions and to improve estimation and forecasting methods related to GHG reductions. Going forward, the Strategy partners will also reevaluate the 2020 GHG emissions goal as needed to align with broader GHG reduction targets established by state, provincial, and federal governments.5 Throughout these efforts, the Strategy partners will seek ways to maximize efciency gains across all sectors and to implement clean, low-carbon fuels in advance of, or surpassing, improvements already expected due to phase-in of regulations and anticipated turnover of eet vehicles and equipment. 4 Although cruise line activities are included in each port's emissions inventory, the two ports with cruise passengers (Port Metro Vancouver and Port of Seattle) have not included cruise passengers in their cargo throughput metrics. In other words, cruise passengers are not accounted for in the "per ton of cargo" gures above. 5 For example, Washington State aims to reduce GHG emissions to 1990 levels by 2020, to 25% below 1990 levels by 2035, and to 50% below 1990 levels by 2050 (Chapter 70.235, Revised Code of WashingtonLimiting Greenhouse Gas Emissions, http://apps.leg.wa.gov/RCW/default.aspx?cite=70.235.020, last accessed October 2013). British Columbia aims to reduce GHG emissions by at least 33% below 2007 levels by 2020 and 80% below 2007 levels by 2050 (available online at www.env.gov.bc.ca/cas/legislation/index. html#GGRTA, last accessed October 2013). Northwest Ports Clean Air Strategy Update 2013 8 Although the Strategy focuses on emissions directly related to port operations, the Strategy partners recognize that the efciency of freight movementand the associated air emissions are tied to transportation infrastructure and trafc systems. Since the ports cannot control the broader transportation system, neither the DPM nor GHG reduction goals assume signicant gains from improvements in regional transportation systems. The Strategy partners, however, will continue to work with regional transportation departments on plans and projects to improve system efciency and reduce emissions. Table 2 summarizes the 2015 and 2020 goals for DPM and GHG emission reductions per ton of cargo. To achieve these goals, the Strategy Update presents actions and performance targets for each sector, as described in the following chapter. Table 2. Emission-Reduction Goals for DPM and GHGs by 2015 and 2020, from 2005 Baseline Targeted Emissions 2015 Goals 2020 Goals Measurement Diesel particulate matter 75% reduction 80% reduction Emissions per ton of cargo Greenhouse gases 10% reduction 15% reduction Emissions per ton of cargo Northwest Ports Clean Air Strategy Update 2013 9 PERFORMANCE TARGETS BY SECTOR Actions and performance targets for reducing emissions to reach the ports' emission-reduction goals for DPM and GHGs are organized by the following port-related emission source sectors: 1. Ocean-going vessels (OGVs) 2. Harbor vessels 3. Cargo-handling equipment (CHE) 4. Trucks 5. Locomotives and rail transport 6. Port administration The following chapters summarize each sector, including covered activities, emissions, relevant regulations, progress, challenges, next steps, actions, and performance targets. Annual implementation reports provide additional information on these sectors and progress to date.6 Figure 2 shows the contributions of each sector to the combined DPM and GHG emissions from the Port of Seattle, Port of Tacoma, and Port Metro Vancouver.7 Because these gures include emissions from port-related travel throughout the airshed, ship movements from the ocean entrance of the Strait of Juan de Fuca to and from the three ports contribute to the large share of emissions from ocean-going vessels. Emissions from these ships are expected to decrease signicantly due to implementation of international emission regulations beginning in 2012. Within the ports themselves, cargo-handling equipment contributes a major portion of emissions. Appendix A provides more information on the port emissions inventories, and Appendix B summarizes relevant air emission regulations in the United States and Canada. 6 Northwest Ports Clean Air Strategy Implementation Reports, available online via all three ports: www.portoftacoma.com/nwpcas, www.portmetrovancouver.com/en/environment/initiatives/air.aspx, and www.portseattle.org/Environmental/Air/Seaport-Air-Quality/ Pages/NWPorts-Clean-Air.aspx, last accessed October 2013. 7 Starcrest Consulting Group, LLC, 2011 Puget Sound Maritime Air Emissions Inventory, May 2013 update; SNC-Lavalin, Port Metro Vancouver 2010 Landside Emissions Inventory, March 26, 2012; SNC-Lavalin, 2010 National Marine Emissions Inventory for Canada, March 31, 2012 (not yet published; available by request from Environment Canada). A working group of the Strategy partners analyzed data from these inventories to develop estimates of combined emissions across the three ports. Northwest Ports Clean Air Strategy Update 2013 10 Figure 2. Port-Related DPM and GHG Emissions by Sector from the Three Ports, 20102011 Note: Figures may not sum to 100% due to rounding. DPM GHGs Diesel Particulate Matter Greenhouse Gases Rail 13% OGVs OGVs 78% 46% Trucks 28% Rail 9% Harbor vessels 4% Harbor CHE 5% Trucks 5% vessels 5% CHE 7% Meeting the sector-specic performance targets will enable the ports to achieve the Strategy Update's emission-reduction goals for DPM and GHGs and to reduce port-related emissions throughout the airshed. Because the size and characteristics of each sector vary across the three ports, the Strategy Update does not set emission-reduction goals by sector. The performance targets apply to all three ports but will be implemented separately by the individual ports. Each port can determine the appropriate balance of actions to achieve the emissionreduction goals. Because the ports do not directly control many of the activities that produce emissions, the Strategy's success relies on signicant contributions from port tenants, customers, and other stakeholders who own and operate port-related vessels and equipment. Tools for implementation include regulations, port procedures and requirements (such as licensing systems, registrations, fees, tariffs, and lease conditions), incentives, grants, recognition programs, pilot studies, demonstration projects, and other methods to encourage voluntary action and behavior change. While regulations are also addressing emissions from these sectors, the voluntary actions in this Strategy Update complement and go beyond these regulations to further reduce emissions. Northwest Ports Clean Air Strategy Update 2013 11 1. OCEAN-GOING VESSELS Activities and Emissions Ocean-going vessels (OGVs or ships) include container ships, tankers, bulk carriers, and cruise ships. These ships typically use large Category 3 marine diesel engines for propulsion and may also have one or several auxiliary engines. Ships burn fuel and generate emissions during transit to and from ports (the emissions inventories include transit between local ports and the Pacic Ocean), maneuvering into or out of port, and hotelling to meet ship power demands while docked or at anchor. OGVs have historically produced relatively high emissions due to their large engines, lack of emission-control devices, and use of high-sulfur fuelalthough they remain a relatively efcient form of transport compared to other modes. The three ports combined receive more than 5,000 calls annually from nearly 2,000 unique vessels. Each port serves multiple different container and cruise lines. In addition, many different bulk, break-bulk, and tanker vessels call at the three ports.8 OGVs produced approximately 78% of DPM emissions and approximately 46% of GHG emissions from activities related to the three ports, as identied in their emissions inventories.9 Regulations Ships move among jurisdictions, and most are registered with countries other than the United States or Canada. The International Maritime Organization (IMO) sets international standards to prevent pollution from ships. In 2010, the IMO designated the North American Emission Control Area (ECA), which includes waters 200 nautical miles or less from the coasts of British Columbia and Washington State and contains the entire Georgia BasinPuget Sound airshed. All vessels within the ECA must burn lower-sulfur fuel or achieve an equivalent emission reduction. The maximum fuel sulfur limit recently decreased to 1%; and in January 2015, the limit goes down to 0.1% sulfur in fuel.10 Appendix B provides more detail on emission regulations for ocean-going vessels. New regulations were put into place in January 2013 following amendments to the International Convention on the Prevention of Pollution from Ships (MARPOL) Annex VI regulations, which address energy-efciency for ships of 400 gross tonnage and above. This new chapter makes mandatory the Energy Efciency Design Index (EEDI), which requires new ships to be more energy-efcient. The regulations are non-prescriptive, as long as the required energy-efciency level is attained, so ship designers and builders are free to use the most cost-efcient solutions for each particular ship. 8 Bulk carriers transport uniform materials such as grain or gravel. Break-bulk, or general cargo, consists of materials not transported in containers, such as goods in bags, boxes, crates, drums, barrels, or pallets. Tanker vessels transport petroleum products or other liquids. 9 Starcrest Consulting Group, LLC, 2011 Puget Sound Maritime Air Emissions Inventory, May 2013 update; SNC-Lavalin, Port Metro Vancouver 2010 Landside Emissions Inventory, March 26, 2012; SNC-Lavalin, 2010 National Marine Emissions Inventory for Canada, March 31, 2012 (not yet published; available by request from Environment Canada). A working group of the Strategy partners analyzed data from these inventories to develop estimates of combined emissions across the three ports. 10 International Maritime Organization, "Information on North American Emission Control Area (ECA) under MARPOL Annex VI," May 13, 2010, www.imo.org/blast/blastDataHelper.asp?data_id=29099&lename=723.pdf, last accessed October 2013. The United States implemented the ECA in August 2012, and Canada began enforcement in May 2013. Transport Canada, "Regulations Amending the Vessel Pollution and Dangerous Chemicals Regulations," www.tc.gc.ca/eng/mediaroom/backgrounders-vessel-pollution-regulations-7162.html, last accessed October 2013. Northwest Ports Clean Air Strategy Update 2013 12 The new regulations also require all ships to have a Ship Energy Efciency Management Plan (SEEMP), which is a fuel-conservation plan involving speed optimization, weather routing, or hull maintenance. By 2025, new vessels must be 30% more energy-efcient, and all vessels must have energy-efciency plans. These new standards are expected to reduce overall GHG emissions from ships by 9% annually by 2025. The United States and Canada are in the process of adopting strict environmental regulations to comply with and implement these international standards. Progress, Challenges, and Next Steps Successful emission reductions have already been achieved through providing shore power and incentives for using lower-sulfur fuels while in port. The annual implementation reports provide more details on existing efforts to date.11 As ECA implementation moves forward, it will signicantly reduce emissions from ships. The ports have limited control over visiting ships and their emissions. Vessels travel all over the world, and some may call at a particular port only once in a year. The ports have the greatest inuence over ships when they are maneuvering in port and hotelling at the dock. Current efforts to reduce emissions include ECA implementation, shore power, nancial incentives to burn cleaner fuel at berth, and stricter emission regulations for marine engines. In addition, this Strategy Update encourages vessel owners and operators to participate in green certication programs and to reduce emissions furthersuch as through efcient ship design and adoption of green operations and practices. Cost and availability of ECA-compliant fuels may pose challenges for shipping lines, but use of lower-sulfur fuel will signicantly reduce DPM emissions. The ports are committed to helping ships surpass the ECA standards for lower-sulfur fuels and assisting with early adoption of the ECA's 2015 fuel sulfur limit, with specic emphasis on hotelling operations. The ports will measure progress through port-designed programs and third-party certication. Such systems encourage best practices and continuous improvement and may also result in lower operating costs. The ports will track and report annually on the number of hotelling vessels using Tier 3 marine engines, shore power, cleaner fuels, and other emission-reduction technologies. The result should be decreases in both DPM and GHG emissions. 11 Northwest Ports Clean Air Strategy Implementation Reports, available online via all three ports: www.portoftacoma.com/nwpcas, www.portmetrovancouver.com/en/environment/initiatives/air.aspx, and www.portseattle.org/Environmental/Air/Seaport-Air-Quality/ Pages/NWPorts-Clean-Air.aspx, last accessed October 2013. Northwest Ports Clean Air Strategy Update 2013 13 Table 3 summarizes actions and performance targets for 2015 and 2020 for the OGV sector. Table 3. Actions and Performance Targets for Ocean-Going Vessels, for 2015 and 2020 Reduces Actions 2015 Targets 2020 Targets DPM GHG OGV-1 Vessels surpass Emission Early compliance with Ports track number Control Area (ECA) 2015 ECA 0.1% fuel- of vessels with Tier 3 requirements sulfur level (or marine engines, shore equivalent) while hotelling power use, cleaner before 2015 fuel, or other emissionreduction technologies OGV-2 Ports and vessels participate Ports and 10% of vessel Ports and 40% of vessel in port-designed or third- calls calls party certication programs that promote continuous improvement (such as Environmental Ship Index, Green Marine, Clean Cargo Working Group, or others) Northwest Ports Clean Air Strategy Update 2013 14 2. HARBOR VESSELS Activities and Emissions Harbor vessels are an important part of the Northwest economy. This sector includes assist and escort tugs, harbor and ocean tugs, ferry vessels, excursion vessels, government vessels, work boats, some commercial shing vessels, and tank barges. Harbor vessels generate air emissions from burning fuels as they move and work in the ports. Fewer than 200 of the approximately 1,000 harbor vessels operating in and near the three ports are directly related to port activity. These port-related harbor vessels are owned and operated by about a dozen companies. Port-related harbor vessels, including tugs and port-owned vessels, account for approximately 4% of DPM emissions and 5% of GHG emissions from activities related to the three ports, as identied in their emissions inventories.12 Recreational vessels and other non-port-related harbor vessels contribute additional emissions but are not covered in this Strategy Update. Regulations Starting in 2012, fuel regulations in the United States and Canada effectively required harbor vessels to use ultra-low-sulfur diesel (ULSD) fuel. Both countries also require new harbor vessel engines to meet stricter emissions standards and specify the installation of upgrade kits during engine overhauls for applicable existing engines. Appendix B provides more information on emission regulations for harbor vessels. Progress, Challenges, and Next Steps The ports have not been directly involved in harbor vessel-related projects to date, although use of lower-sulfur fuel by some harbor vessel operators ahead of regulatory requirements has reduced emissions from harbor vessels. The Puget Sound Clean Air Agency has received several grants over the last few years from Ecology, U.S. EPA, and the U.S. Department of Transportation's Maritime Administration for diesel reduction projects on harbor vessels. In partnership with vessel owners, these grants have upgraded engines on a shing boat, helped investigate exhaust retrots to reduce DPM emissions, and will repower two tugs. Ferries in Washington State and British Columbia have also undertaken multiple efforts to reduce their fuel use and emissions. Annual implementation reports provide additional information regarding harbor vessels.13 Ports have little inuence over harbor vessels because they do not have direct business relationships with most harbor vessel owners and operators. The most effective way to reduce emissions from harbor vessels is to replace the vessels or repower them (replace their engines), 12 Starcrest Consulting Group, LLC, 2011 Puget Sound Maritime Air Emissions Inventory, May 2013 update; SNC-Lavalin, Port Metro Vancouver 2010 Landside Emissions Inventory, March 26, 2012; SNC-Lavalin, 2010 National Marine Emissions Inventory for Canada, March 31, 2012 (not yet published; available by request from Environment Canada). A working group of the Strategy partners analyzed data from these inventories to develop estimates of combined emissions across the three ports. 13 Northwest Ports Clean Air Strategy Implementation Reports, available online via all three ports: www.portoftacoma.com/nwpcas, www.portmetrovancouver.com/en/environment/initiatives/air.aspx, and www.portseattle.org/Environmental/Air/Seaport-Air-Quality/ Pages/NWPorts-Clean-Air.aspx, last accessed October 2013. Northwest Ports Clean Air Strategy Update 2013 15 but these efforts are expensive. Exhaust retrots to reduce DPM emissions are available for some engines. Although exhaust retrots are a fraction of the cost of repowers, they are still expensive, have limited applications, and do not reduce fuel use (and thus they do not decrease GHG emissions or fuel costs). The Strategy Update focuses on port-related harbor vessels and does not address emissions from non-port-related harbor vesselswhich include ferries, recreational vessels, and non-portrelated tugs. The Strategy partners believe promoting increased vessel fuel efciency and best practices is the best way to work with this sector. Accordingly, the Strategy partners will identify activities that increase fuel efciency and reduce emissions, and they will share this information with harbor vessel owners and operators to foster adoption of best practices. Table 4 summarizes actions and performance targets for 2015 and 2020 for harbor vessels. Table 4. Actions and Performance Targets for Harbor Vessels, for 2015 and 2020 Reduces Actions 2015 Targets 2020 Targets DPM GHG Harbor-1 Strategy partners conduct Partners conduct Partners conduct annual outreach to port- outreach and 50% outreach and 90% related harbor vessel of harbor vessel of harbor vessel companies and recognize companies report best companies report best best practices and engine practices and engine practices and engine upgrades upgrades upgrades Harbor-2 Ports and harbor vessels Ports and 10% of Ports and 40% of participate in port-designed harbor vessels harbor vessels or third-party certication programs that promote continuous improvement (such as Environmental Ship Index, Green Marine, Clean Cargo Working Group, or others) Northwest Ports Clean Air Strategy Update 2013 16 3. CARGO-HANDLING EQUIPMENT Activities and Emissions Cargo-handling equipment (CHE) moves goods to and from ships, railcars, and trucks. The equipment addressed in this Strategy Update includes, but is not limited to, the following equipment operated on marine terminals: straddle carriers, rubber-tired gantry (RTG) cranes, reach stackers, top and side picks, forklifts, skid loaders, yard tractors and trucks, wharf cranes, and conveyor belts. The performance targets for CHE apply to equipment operating more than 100 hours per year with greater than 25 brake horsepower (bhp). The three ports combined are using an estimated 3,000 pieces of cargo-handling equipment, the majority of which are diesel-powered. Much of this equipment is owned and operated by port tenants and other users, rather than the ports themselves. The CHE sector contributes 5% of DPM emissions and 7% of GHGs from activities related to the three ports, as identied in their emissions inventories.14 Regulations New engines on cargo-handling equipment in both the United States and Canada are subject to federal air quality regulations, which establish tiers of emission standards based on engine output capacity and year of manufacture. Appendix B provides more information on emission regulations for cargo-handling equipment. Progress, Challenges, and Next Steps Using a variety of federal, state, local, and port grant funds, terminal operators have been working with the Strategy partners to upgrade, repower, or retrot existing CHE with cleaner engines or best-available control technology for reducing emissions. The ports have conducted pilot studies of retrots and cleaner-fueled equipment, including electric or hybrid-electric CHE. These studies have provided valuable operational experience to inform future efforts. The terminal operators have provided in-kind contributions for project oversight, implementation, and maintenance costs associated with emission-control technology and equipment. They have also purchased newer, cleaner equipment. Annual implementation reports provide additional information regarding cargo-handling equipment.15 Replacement, repowering, or exhaust retrots can reduce emissions from cargo-handling equipment, although the high cost of replacement engines and failure of one type of exhaust control for DPM have hampered emission-reduction efforts. Relatively few options for retroteligible equipment are available, and replacing equipment before the end of its useful life can be cost-prohibitive. Although retrots can reduce emissions and fuel use, they may increase other 14 Starcrest Consulting Group, LLC, 2011 Puget Sound Maritime Air Emissions Inventory, May 2013 update; SNC-Lavalin, Port Metro Vancouver 2010 Landside Emissions Inventory, March 26, 2012; SNC-Lavalin, 2010 National Marine Emissions Inventory for Canada, March 31, 2012 (not yet published; available by request from Environment Canada). A working group of the Strategy partners analyzed data from these inventories to develop estimates of combined emissions across the three ports. 15 Northwest Ports Clean Air Strategy Implementation Reports, available online via all three ports: www.portoftacoma.com/nwpcas, www.portmetrovancouver.com/en/environment/initiatives/air.aspx, and www.portseattle.org/Environmental/Air/Seaport-Air-Quality/ Pages/NWPorts-Clean-Air.aspx, last accessed October 2013. Northwest Ports Clean Air Strategy Update 2013 17 operating and maintenance costs. Equipment powered on cleaner fuels, such as compressed or liqueed natural gas (CNG or LNG), propane, or electricity holds promise for emission reductions. However, fuel availability, additional infrastructure cost, reduced cargo capacity, and shortened run times before refueling pose challenges for integrating such equipment into existing systems. Through pilot studies undertaken since 2008, Strategy partners and equipment operators have gained extensive knowledge about the technology and operational challenges of the current generation of low-emission CHE. As technology and fueling infrastructure improve, the ports will aggressively evaluate cleaner and renewable energysuch as electricity, propane, CNG, LNG, and biofuelsto reduce DPM and GHG emissions from cargo-handling equipment. Alternative fuels also reduce GHGs; such fuels will be evaluated to determine if they meet the Tier 4 interim targets.16 More efcient use of equipment will also help reduce emissions. Table 5 summarizes actions and performance targets for 2015 and 2020 for cargo-handling equipment. Table 5. Actions and Performance Targets for Cargo-Handling Equipment, for 2015 and 2020 Reduces Actions 2015 Targets 2020 Targets DPM GHG CHE-1 CHE meets Tier 4 interim 50% of equipment 80% of equipment (T4i) emission standards or equivalent 16 CHE-2 Ports and terminals have Ports and 50% of Ports and 100% of fuel-efciency plans in place terminals terminals that promote continuous improvement 16 Tier 4 refers to a set of emission requirements established by the U.S. Environmental Protection Agency to reduce emissions of particulate matter, which is a focus of this Strategy. Additionally, the requirements also address nitrogen oxides (NO ) and air toxics X from new, non-road diesel engines. Tier 4i, or interim, refers to the New Source Performance Standards for emissions that became effective on January 1, 2011, for all new, high-horsepower diesel generator engines. The Tier 4i standard signicantly cuts NO X emissions. Northwest Ports Clean Air Strategy Update 2013 18 4. TRUCKS Activities and Emissions The truck sector covers on-road heavy-duty trucks that move cargo to and from marine terminals. Trucks deliver cargo and containers to and from local and national destinations, and they also transfer loads between terminals, distribution centers, and intermodal loading facilities. Most of these trucks are Class 8 heavy-duty vehicles, with gross vehicle weights of more than 33,000 pounds. Approximately 9,000 heavy-duty trucks transport cargo to and from the three ports, accounting for an estimated 6 million roundtrips through the terminal gates each year. Trucks account for 5% of DPM emissions and 28% of GHGs from activities related to the three ports, as identied in their emissions inventories.17 Regulations In both the United States and Canada, the federal government regulates fuels, emission-control components, and emission standards for heavy-duty trucks. Truck emission standards address particulates, hydrocarbons, nitrogen oxides, and carbon monoxide. GHG emission standards for heavy-duty vehicles take effect starting with model year 2014 engines. Appendix B provides more information on emission regulations for trucks. Progress, Challenges, and Next Steps The three ports have established their own approaches to achieving air quality requirements for heavy-duty trucks entering their marine terminals. Annual implementation reports describe efforts to date.18 The ports achieved their 2010 target for heavy-duty trucks calling at marine terminals to meet the model year 1994 engine emissions standard or equivalent. The ports adopted requirements for trucks entering their container terminals to be enrolled in either a truck licensing system or a truck registry, which documents that trucks meet the emission requirements. Model year 1994 engines are 2.5 to 6 times cleaner than pre-1994 truck engines for DPM emissions.19 Typically, heavy-duty trucks are not owned by the ports, marine terminals, or shippers. Most trucks are either independently owned and operated or owned by transport companies. The most effective methods to reduce DPM emissions are to replace the vehicles or repower them (replace their engines). Both of these measures are costly, and truck owners may need to spread the costs of their investments over long time spans. 17 Starcrest Consulting Group, LLC, 2011 Puget Sound Maritime Air Emissions Inventory, May 2013 update; SNC-Lavalin, Port Metro Vancouver 2010 Landside Emissions Inventory, March 26, 2012; SNC-Lavalin, 2010 National Marine Emissions Inventory for Canada, March 31, 2012 (not yet published; available by request from Environment Canada). A working group of the Strategy partners analyzed data from these inventories to develop estimates of combined emissions across the three ports. 18 Northwest Ports Clean Air Strategy Implementation Reports, available online via all three ports: www.portoftacoma.com/nwpcas, www.portmetrovancouver.com/en/environment/initiatives/air.aspx, and www.portseattle.org/Environmental/Air/Seaport-Air-Quality/ Pages/NWPorts-Clean-Air.aspx, last accessed October 2013. 19 The U.S. EPA emission standard for particulate matter for model year 19881993 engines was 0.25 to 0.60 grams per brake horsepower-hour (bhp-hr). For model year 1994 engines, it was 0.1 grams/bhp-hr; and for model year 2007 engines, 0.01 grams/ bhp-hr. (DieselNet, "Emission Standards: Heavy-Duty Truck and Bus Engines," www.dieselnet.com/standards/us/hd.php#y2007, last accessed October 2013.) Northwest Ports Clean Air Strategy Update 2013 19 The next phase of the ports' clean truck programs calls for trucks to meet 2007 emission standards by the end of 2017. A 2007 engine is ten times cleaner than a 1994 engine for DPM emissions.20 These newer trucks are more expensive to purchase and more costly to maintain, however. Because engine emission standards addressing GHGs do not take effect until the 2014 model year, performance targets to reduce GHG emissions are focused on improving efciency and reducing fuel use. However, a trend toward alternative technologies and cleaner fuels in the intervening years may also reduce GHG emissions. Such efforts will also reduce DPM emissions. Emission standards for post-2007 model year engines do not signicantly reduce DPM emissions. Instead, they focus on reducing other pollutants and improving fuel economy, which reduces GHG emissions. A potential future target (beyond the year 2020) may be for trucks entering ports to meet the 2014 emission standards. Recognizing that the broader transportation system greatly inuences the efciency of truck movement outside of port terminals, the ports will continue to work with regional transportation departments and air agencies to adopt programs such as faster freight corridors, priority treatment, and freight-only capacity expansions to move freight more quickly on roads and rail facilities. Table 6 summarizes actions and performance targets for 2015 and 2020 for the truck sector. Table 6. Actions and Performance Targets for Trucks, for 2015 and 2020 Reduces Actions 2015 Targets 2020 Targets DPM GHG Truck-1 Trucks meet or surpass 100% of trucks by the end of 2017 U.S. EPA emission standards or equivalent for model year 2007 Truck-2 Ports, terminals, and Ports Ports, terminals, and trucks have fuel-efciency 50% of trucks plans in place that promote continuous improvement 20 DieselNet, "Emission Standards: Heavy-Duty Truck and Bus Engines," page 18, www.dieselnet.com/standards/us/ hd.php#y2007, last accessed October 2013. Northwest Ports Clean Air Strategy Update 2013 20 5. LOCOMOTIVES AND RAIL TRANSPORT Activities and Emissions The port-related rail sector consists of locomotives that move railcars within a rail yard (switching or yard locomotives, also known as "switchers") or move trains across the airshed and beyond (line-haul locomotives). Some switchers are operated by port tenants; others are operated by regional and national rail companies working at or near port properties. Switcher locomotives are typically lower horsepower engines that do not leave the yard and travel an average of 6 miles per day. Operators of line-haul locomotives are typically regional or national rail carriers. Line-haul locomotives use higher-horsepower engines and carry freight long distances across state lines and around the United States and Canada. Several hundred locomotives operate at or near the three ports. Locomotive emissions contribute approximately 9% of DPM emissions and 13% of GHGs from activities related to the three ports, as identied in their emissions inventories.21 Regulations Federal fuel regulations in both countries effectively required locomotives to use ultra-lowsulfur diesel (ULSD) fuel beginning in 2012. The U.S. Environmental Protection Agency also sets emissions standards for new and remanufactured locomotive engines. U.S. EPA requires upgrades during overhauls on certain existing engines and requires idle-reduction technology on all new engines and required engine upgrades. Canadian targets to reduce GHG emissions and criteria air pollutants align with U.S. EPA's emission standards for locomotives. Appendix B provides more information on emission regulations for the rail sector. Progress, Challenges, and Next Steps The ports have not been directly involved in locomotive projects to date. The Puget Sound Clean Air Agency and Washington State Department of Ecology have conducted several grantfunded projects to reduce emissions, including the repower of three local switcher locomotives under a U.S. EPA grant and the installation of idle-reduction technology on several other locomotives. As a result of 2012 federal fuel regulations requiring the use of ULSD, the rail sector has substantially reduced DPM and sulfur emissions, and some rail operators began using lower-sulfur fuel prior to the regulations. Under its SmartWay Program, EPA developed the Rail Carrier FLEET tool to enable rail carriers to establish baseline emissions per ton-mile and then track emission reductions.22 21 Starcrest Consulting Group, LLC, 2011 Puget Sound Maritime Air Emissions Inventory, May 2013 update; SNC-Lavalin, Port Metro Vancouver 2010 Landside Emissions Inventory, March 26, 2012; SNC-Lavalin, 2010 National Marine Emissions Inventory for Canada, March 31, 2012 (not yet published; available by request from Environment Canada). A working group of the Strategy partners analyzed data from these inventories to develop estimates of combined emissions across the three ports. 22 SmartWay Transport Partnership, U.S. Environmental Protection Agency, Rail Carrier 2.0.12 Tool: Getting Started Guide2012 Data YearUnited States Version (Part 1), www.epa.gov/smartway/documents/partnership/rail/partnership/420b13010.pdf, last accessed October 2013. Northwest Ports Clean Air Strategy Update 2013 21 Several tenants that operate switchers are using newer low-emission models, some of which incorporate automatic idle-shutdown technology or hybrid-electric engines. Additionally, Port Metro Vancouver and rail service providers have developed a collaborative supply-chain agreement to improve operational efciency that resulted in a 30% reduction in dwell times to less than three days. Annual implementation reports provide more information for the rail sector.23 Because the national, regional, and yard locomotive companies operate differently, the ports will tailor their emission-reduction approaches. The ports have very little inuence over line-haul locomotives or most switchers, which are operated by major rail companies working throughout the United States and Canada. The Strategy partners will focus on reducing emissions from locally managed switcher locomotives operating at or near the ports. Many locomotives in operation have engines that were installed before 1973, and regulations apply only to newer locomotive engines (life expectancy of a locomotive is approximately 50 years). Additionally, U.S. EPA does not certify retrot kits for locomotive engines manufactured prior to 1973. Emission-reduction efforts, such as participating in EPA's voluntary SmartWay program and installing idle-reduction technologies, provide some nancial incentive for rail companies to reduce emissions. Recognizing that the broader transportation system inuences the efciency of rail movement outside of port terminals, the ports will continue to work with regional transportation departments and air agencies to adopt programs such as faster freight corridors, priority treatment, and freight-only capacity expansions to move freight more quickly on both rail facilities and roads. Table 7 summarizes actions and performance targets for 2015 and 2020 for locomotives and rail transport. Table 7. Actions and Performance Targets for Locomotives and Rail Transport, for 2015 and 2020 Reduces Actions 2015 Targets 2020 Targets DPM GHG Rail-1 Switcher locomotive 100% of owners/ 100% of owners/ owners/operators operators institute a operators achieve participate in a fuel- program performance objectives efciency program of chosen program Rail-2 Switcher locomotive owners/ 10% of unregulated 20% of unregulated operators upgrade or locomotive engines locomotive engines replace unregulated engines (engine replacements will be Tier 2 or better) 23 Northwest Ports Clean Air Strategy Implementation Reports, available online via all three ports: www.portoftacoma.com/nwpcas, www.portmetrovancouver.com/en/environment/initiatives/air.aspx, and www.portseattle.org/Environmental/Air/Seaport-Air-Quality/Pages/NWPorts-Clean-Air.aspx, last accessed October 2013. Northwest Ports Clean Air Strategy Update 2013 22 6. PORT ADMINISTRATION Activities and Emissions While most port-related emissions come from vehicles or equipment that the ports themselves do not operate, the Strategy partners recognize that the ports have their own administrationrelated emissions that can be reduced. The administration sector covers sources that are governed directly by the ports such as port-owned vehicles and vessels, ofce buildings, support facilities, and employee functions. The associated activity-related emissions include eet fuel use, facility energy consumption, employee commuting, materials use, waste management, and maintenance and construction projects. Regulations Most of the emission-reduction efforts in the port administration sector are voluntary. In Washington State, large employers are required to implement employee commute trip reduction programs. Progress, Challenges, and Next Steps The ports are committed to seeking ways to reduce their own emissions, in addition to facilitating emission reductions by their tenants, customers, and other stakeholders. Some examples of port initiatives include purchasing cleaner-fueled vehicles, constructing LEED- certied buildings, diverting solid waste from landlls, conducting energy audits, conserving energy, retrotting HVAC systems in buildings, conducting corporate (administrative) carbon footprints, and purchasing offsets for greenhouse gas emissions.24 The original Strategy did not include specic requirements for reporting on the status of the vehicles, equipment, and vessels in their eets. In future implementation reports, the ports will describe the number and type of engines in use each year; the number and type of emissionrelated retrots installed; the quantity and types of fuels used; and other information relevant to air emissions. The ports will also continue to report progress on various administrative initiatives to reduce air emissions and help protect the climate. Two new focus areas include reducing emissions from on-road, non-road, and marine engines used on port-led construction projects as well as facilitating energy conservation at both port-operated and tenant facilities. 24 More information on port activities is included in the Northwest Ports Clean Air Strategy Implementation Reports, available online via all three ports: www.portoftacoma.com/nwpcas, www.portmetrovancouver.com/en/environment/initiatives/air.aspx, and www.portseattle.org/Environmental/Air/Seaport-Air-Quality/Pages/NWPorts-Clean-Air.aspx, last accessed October 2013. Northwest Ports Clean Air Strategy Update 2013 23 Table 8 summarizes actions and performance targets for 2015 and 2020 for port administration. Table 8. Actions and Performance Targets for Port Administration, for 2015 and 2020 Reduces Actions 2015 Targets 2020 Targets DPM GHG Admin-1 Ports own and operate Ports report use of Ports increase use of cleaner vehicles and cleaner vehicles and cleaner vehicles and equipment and have fuel- equipment and other equipment efciency plans in place relevant information that promote continuous improvement Admin-2 Ports apply clean Ports adopt clean Ports continue construction standards construction to apply clean to engines used on port-led practices for port-led construction practices construction projects (such projects, including for port-led projects, as American Association of idle- reduction including idle-reduction Port Authorities' Sustainability requirements, and requirements, and Checklist, U.S. EPA Best enact a plan to address enact a plan to address Practices for Clean Diesel Tier 2 engine emission Tier 4 engine emission Construction, or equivalent requirements requirements best management practices) Admin-3 Ports facilitate energy Each port conducts 3 Each port completes studies and conservation energy studies 3 energy conservation projects at port-operated projects and/or tenant facilities to identify and address energy conservation opportunities in building systems, operations, and yard lighting Northwest Ports Clean Air Strategy Update 2013 24 PILOT STUDIES & DEMONSTRATION PROJECTS Pilot studies and demonstration projects are important for advancing new and existing emissionreduction technology for the maritime industry. To achieve the objectives of this Strategy Update, the Strategy partners have and will continue to invest in pilot studies and demonstration projects that advance emission reductions in the Georgia BasinPuget Sound airshed. The Strategy partners dene pilot studies and demonstration projects as follows: A pilot study is a small-scale preliminary study conducted to evaluate feasibility, time, cost, adverse events, and other factors in an effort to predict and improve upon the study design prior to conducting a full-scale project. Pilot studies are carried out before largescale projects in an effort to avoid wasting time and money on an inadequately designed project. Pilot studies can provide quantitative support that a system has the potential to succeed on a full-scale basis or help identify design changes to yield better results. A demonstration project is a small-scale implementation project that tests feasibility and effectiveness of a technology or change in operation in a real-world application. Examples of pilot studies and demonstration projects conducted at the three ports appear below. Marine liqueed natural gas study. Port Metro Vancouver has partnered with industry to study the feasibility of liqueed natural gas as a cleaner fuel for the marine sector. The study will assess the opportunities and barriers to introducing LNG infrastructure and will be completed in late 2013. Container terminal clean energy. Port Metro Vancouver conducted a study in 2011 to assess the feasibility for cleaner energy sources at two container terminals, focusing on electrication and hybridization of rubber-tired gantry cranes (RTGs). Preliminary engineering designs and cost estimates were produced, which could inform a potential demonstration project. Idle-reduction for cargo-handling equipment. The Puget Sound Clean Air Agency is implementing a demonstration project to install idle-reduction technology on cargohandling equipment at the ports of Seattle and Tacoma. This project is funded by a grant from the Washington State Department of Ecology. Radio-frequency truck tags. The Port of Seattle conducted a pilot study with Stevedoring Services of America to equip more than 1,000 trucks with radio-frequency identication (RFID) tags and install RFID readers at a terminal. Following completion of the pilot, the port developed plans to implement RFID technology at its four container terminals to reduce gate times and improve terminal efciency. Northwest Ports Clean Air Strategy Update 2013 25 Yard truck diesel particulate lter retrot. The Husky terminal at Port of Tacoma participated in a diesel particulate lter (DPF) retrot pilot study with support from U.S. EPA, Puget Sound Clean Air Agency, Port of Seattle, and Port of Tacoma. The purpose of the study was to demonstrate an active DPF system that would be successful on a yard truck subject to signicant idling. Pluggable hybrid-electric terminal truck. The Capacity truck company of Texas provided a hybrid-electric yard truck for demonstration and evaluation at the Port of Tacoma. Three terminals evaluated the equipment over two weeks. Each port will evaluate or engage in at least one pilot study or demonstration project each year to advance their knowledge of port-related emissions and status of performance targets. The ports will convene workshops, webinars, or meetings among relevant stakeholders to share information and results. Findings from pilot studies and demonstration projects will be summarized in the annual implementation reports. Northwest Ports Clean Air Strategy Update 2013 26 PERFORMANCE REPORTING The Strategy partners will participate in ongoing collaboration, including planning, implementing, reviewing, and improving the actions undertaken to meet emission-reduction goals. The approach is voluntary and strategic and will be conducted through collaborative relationships with owners and operators of ocean-going and harbor vessels, cargo-handling equipment, trucks, and locomotives. Strategy implementation uses the following approach to foster continuous improvement: Plan: Each port will develop specic implementation initiatives to meet the emission- reduction goals and performance targets outlined in the Strategy Update. Do: As initiatives are conducted, the Strategy partners will measure performance and share information among participants working to achieve results. Check: Collectively, the Strategy partners will assess results, analyze trends, and report progress each year. Act: Based on results, the Strategy partners will make changes to foster continuous improvement and reinforce activities that achieve results. Implementation Reports and Emissions Inventories The ports will track and report progress toward achieving each performance target for 2015 and 2020. The Strategy partners will also evaluate the number and outcomes of pilot studies and demonstration projects conducted each year as well as workshops held with Strategy partners. Each year, the Strategy partners will publish an implementation report documenting progress toward emission-reduction goals and performance targets. Each port will collect and manage data within its own tracking system or database.25 After 2015 and 2020 (every ve years), the Strategy partners will report estimates of DPM and GHG emissions reduced as a result of these activities, in conjunction with the preparation of updated air emissions inventories. 25 In some cases, such as certain harbor vessel categories and non-container heavy-duty trucks, other government agencies will be responsible for data collection. Northwest Ports Clean Air Strategy Update 2013 27 CONCLUSIONS AND NEXT STEPS This Strategy Update presents airshed-wide goals for reducing port-related emissions of DPM and GHGs as well as 2015 and 2020 performance targets for each sector. Meeting the performance targets will help to achieve the goals for emission reductions in the airshed. Each year, the ports will track progress and present efforts to date in an implementation report. Movement of goods and passengers at the ports is so intertwined that each organization can contribute only part of the solution. The Strategy partners acknowledge that the success of this effort relies on the signicant contributions of port tenants, customers, and other stakeholders who may be directly responsible for the equipment and operations addressed by the emissionreduction actions outlined in this Strategy Update. New and upcoming regulationssuch as the Emission Control Area, MARPOL Annex for GHGs, and 20142018 standards for GHG emissions from truckswill help reduce port-related emissions. To complement and go beyond these regulations, the Strategy partners will undertake initiatives to engage stakeholders in voluntary efforts to further reduce emissions and support a sustainable maritime economy throughout the Georgia BasinPuget Sound region. Northwest Ports Clean Air Strategy Update 2013 28 GLOSSARY AAPA ..............................American Association of Port Authorities B.C. ................................British Columbia Bhp .................................Brake horsepower Bhp-hr ............................Brake horsepower-hour Black carbon .................A solid carbon particle, or aerosol, formed through incomplete combustion that contributes to warming of the atmosphere CHE ................................Cargo-handling equipment CNG ................................Compressed natural gas CO ..................................Carbon monoxide CO .................................Carbon dioxide, a greenhouse gas 2 CO e ...............................Carbon dioxide equivalent 2 DPM ................................Diesel particulate matter ECA ................................Emission Control Area Ecology ..........................Washington State Department of Ecology EEDI ...............................Energy Efciency Design Index EPA ................................United States Environmental Protection Agency GHG ................................Greenhouse gas, a gas that absorbs radiation and contributes to warming of the atmosphere; major GHGs include carbon dioxide (CO ), methane (CH ), nitrous oxide (N O), hydrouorocarbons 2 4 2 (HFCs), peruorocarbons (PFCs), and sulfur hexauoride (SF ) 6 Goals ..............................Airshed-wide objectives for reducing port-related diesel particulate matter and greenhouse gas emissions HDV ................................Heavy-duty vehicle HVAC ..............................Heating, ventilation, and air-conditioning IMO .................................International Maritime Organization LEED ..............................Leadership in Energy and Environmental Design LNG ................................Liqueed natural gas Northwest Ports Clean Air Strategy Update 2013 29 MARPOL ........................International Convention for the Prevention of Pollution from Ships NO .................................Nitrogen oxides X OGVs ..............................Ocean-going vessels Partners ..........................See Strategy partners below Performance targets .....Sector-specic actions for achieving emission reductions PM ..................................Particulate matter PM ................................Particulate matter less than 2.5 microns in diameter (ne particulates) 2.5 PM ................................Particulate matter less than 10 microns in diameter (coarse particulates) 10 Ports ..............................Port of Seattle, Port of Tacoma, and Port Metro Vancouver PSCAA ...........................Puget Sound Clean Air Agency Repower ........................Replacing the engine in a vehicle, vessel, or piece of equipment with a newer, cleaner-running engine RFID ...............................Radio-frequency identication RTG ................................Rubber-tired gantry Sectors ..........................Port-related emission source categories: ocean-going vessels, harbor vessels, cargo-handling equipment, trucks, locomotives and rail transport, and port administration. SEEMP ...........................Ship Energy Efciency Management Plan SO .................................Sulfur dioxide 2 SO .................................Sulfur oxides X Strategy .........................Northwest Ports Clean Air Strategy (originally adopted in 2007), a plan implemented by the three ports and government agencies to reduce port-related emissions that affect air quality and climate change in the Pacic Northwest through a collaborative approach led by the Port of Seattle and Port of Tacoma in Washington State and Port Metro Vancouver in British Columbia. Strategy partners ..........Port of Seattle, Port of Tacoma, and Port Metro Vancouver; Environment Canada; Metro Vancouver; U.S. Environmental Protection Agency; Washington State Department of Ecology; and Puget Sound Clean Air Agency Strategy Update ............Northwest Ports Clean Air Strategy2013 Update T4i ..................................U.S. EPA Tier 4 interim emissions standards for non-road engines Northwest Ports Clean Air Strategy Update 2013 30 ULSD ..............................Ultra-low-sulfur diesel U.S. .................................United States U.S. EPA ........................United States Environmental Protection Agency (also EPA) VOC ................................Volatile organic compound Northwest Ports Clean Air Strategy Update 2013 31 APPENDICES Appendix A. Port Emissions Inventories Appendix B. Air Emission Regulations in the United States and Canada Appendix C. Summary of Public Comments Northwest Ports Clean Air Strategy Update 2013 32 APPENDIX A. PORT EMISSIONS INVENTORIES Port-related activities are a signicant source of air emissions. In recognition that air emissions are not constrained by jurisdictional boundaries and freely cross borders, the three ports and regional, provincial, state, and federal air quality management programs collaborated on the development of the emissions inventories and the Northwest Ports Clean Air Strategy. The ports' emissions inventories guide the direction of this Strategy Update, and they form the basis of the airshed emission-reduction goals and sector-specic performance targets. The 20102011 emissions data illustrate the considerable progress made since the 2005 baseline inventories, through actions of ports and other stakeholders as well as implementation of regulations to reduce emissions. Puget Sound Maritime Air Emissions Inventory 2011 The 2011 Puget Sound Maritime Air Emissions Inventory covers port-related activities in the area shown in Figure A-1, bounded by the black dotted lines. The Puget Sound emissions inventory includes separate inventories for the Port of Seattle and Port of Tacoma as well as other Puget Sound ports. Figure A-1. Puget Sound Maritime Emissions Inventory Boundaries Bellingham S t Victoria r a i t o f J u a n d e F u c a Puget Port Sound Angeles Seattle Tacoma Port Authority Olympia Airshed Boundary 0 15 30 45 60 Kilometers 0 10 20 30 40 Miles I Northwest Ports Clean Air Strategy Update 2013 33 Air emissions from the Port of Seattle and Port of Tacoma in 2011 are summarized in Table A-1 and Table A-3, respectively. Following the summary of total emissions for each port, Table A-2 and Table A-4 show emission reductions from 2005 to 2011 for each port. For more details, please refer to the full emissions inventory report for 2011.26 Table A-1. Port of Seattle2011 Emissions Inventory for Puget Sound Airshed (tons) Source NO VOC CO SO PM PM DPM CO e x 2 10 2.5 2 OGV, hotelling & 748 26 66 601 48 38 39 54,479 maneuvering OGV, transit 4,106 158 366 3,151 265 212 258 202,078 Harbor vessels 418 24 82 <1 16 15 16 25,048 Recreational vessels 57 62 614 <1 1 1 <1 7,083 Locomotives 680 42 111 6 25 23 25 41,870 Cargo-handling 306 18 158 <1 17 16 17 34,561 equipment Heavy-duty vehicles 1,270 83 390 2 25 23 25 206,887 Terminal eet vehicles 3 1 12 <1 <1 <1 <1 1,053 Total 7,588 414 1,799 3,760 397 328 380 573,059 Note: Figures are rounded to the nearest ton and may not sum to exact totals shown due to rounding. Table A-2. Port of SeattleChanges in Port Airshed Emissions from 2005 to 2011 % Change NO VOC CO SO PM PM DPM CO e x 2 10 2.5 2 OGV, hotelling & -13% -7% -8% -39% -35% -35% -34% -10% maneuvering OGV, transit -27% -20% -21% -11% -21% -21% -21% -11% Harbor vessels -22% -8% -14% -100% -27% -26% -27% -16% Recreational vessels -20% -60% -41% -93% -57% -56% -26% -15% Locomotives -34% -19% -15% -93% -14% -14% -14% -13% Cargo handling -27% -64% -74% -99% -40% -40% -39% -9% equipment Heavy-duty vehicles -16% 10% -16% -96% -53% -53% -53% 8% Terminal eet vehicles -43% -70% -60% 20% 67% 60% -19% -25% Total -25% -29% -38% -21% -27% -28% -27% -5% Note: Negative numbers indicate reductions in emissions, and positive numbers indicate increases in emissions. 26 Starcrest Consulting Group, LLC, 2011 Puget Sound Maritime Air Emissions Inventory, May 2013 update, www.pugetsoundmaritimeairforum.org, last accessed October 2013. Northwest Ports Clean Air Strategy Update 2013 34 Table A-3. Port of Tacoma2011 Emissions Inventory for Puget Sound Airshed (tons) Source NO VOC CO SO PM PM DPM CO e x 2 10 2.5 2 OGV, hotelling & 375 12 32 410 29 23 21 30,273 maneuvering OGV, transit 3,257 122 280 2,562 216 173 203 153,472 Commercial harbor 291 10 44 <1 12 11 12 17,485 vessels Locomotives 520 33 80 4 18 16 18 30,030 Cargo-handling 206 13 88 <1 10 10 10 22,486 equipment Heavy-duty vehicles 895 51 229 1 17 15 17 141,618 Terminal eet vehicles 3 1 14 <1 <1 <1 <1 1,429 Total 5,546 241 768 2,977 303 249 281 396,792 Note: Figures are rounded to the nearest ton and may not sum to exact totals shown due to rounding. Table A-4. Port of TacomaChanges in Port Airshed Emissions from 2005 to 2011 % Change NO VOC CO SO PM PM DPM CO e x 2 10 2.5 2 OGV, hotelling & -42% -41% -41% -39% -38% -38% -38% -36% maneuvering OGV, transit -20% -15% -15% -6% -12% -12% -13% -8% Commercial harbor 4% 64% 17% -99% -3% -3% -3% 11% vessels Locomotives -50% -36% -37% -95% -35% -36% -35% -35% Cargo-handling -44% -51% -45% -96% -56% -56% -57% -42% equipment Heavy-duty vehicles -32% -20% -39% -97% -63% -64% -63% -16% Terminal eet vehicles -36% -45% -9% 33% 0% -5% -50% -15% Total -28% -23% -30% -16% -25% -26% -26% -18% Note: Negative numbers indicate reductions in emissions, and positive numbers indicate increases in emissions. Northwest Ports Clean Air Strategy Update 2013 35 Port Metro Vancouver Landside Emissions Inventory 2010 The Port Metro Vancouver emissions inventory covers port-related activities in the area shown in Figure A-2, bounded by the red box. The landside activities are reported in the updated 2010 Landside Emissions Inventory,27 and the marine activities are reported for the port's jurisdictional area, referred to as Region 2, in Environment Canada's 2010 National Marine Emissions Inventory. The combination of the two inventories provides valuable insight into emission sources and the effects of emission-reduction measures. Port Metro Vancouver conducted emissions inventories in 2005 and 2010. The two inventories differ substantially, however, primarily due to the amalgamation in 2008 of the Fraser River Port Authority, the North Fraser Port Authority, and the Vancouver Port Authority. The 2010 inventory covers the combined Port Metro Vancouver and thus contains a great deal more activity. The 2005 and 2010 inventories for marine emissions were also conducted by different entities using signicantly different methodologies. The total 2010 emissions are provided in Table A-5. Figure A-2. Port Metro VancouverEmissions Inventory Boundaries 27 SNC-Lavalin, Port Metro Vancouver 2010 Landside Emissions Inventory, March 26, 2012, www.portmetrovancouver.com/en/ environment/initiatives/air.aspx, last accessed October 2013. SNC-Lavalin, 2010 National Marine Emissions Inventory for Canada, March 31, 2012 (not yet published; available by request from Environment Canada). Northwest Ports Clean Air Strategy Update 2013 36 Table A-5. Port Metro Vancouver2010 Emissions Estimates for Lower Fraser Valley Airshed (metric tons) Criteria Air Contaminants GHGs Source NO VOC CO SO PM PM CO x x 10 2.5 2 Ocean-going vessels 28 7,932 582 750 4,604 568 522 430,178 Cargo-handling equipment 29 643 83 774 1 41 40 65,624 Rail locomotives 29 2,853 111 291 15 93 85 161,934 Trucks and terminal eet 823 38 220 1 13 10 97,935 vehicles 29 Total 12,251 815 2,034 4,621 714 657 755,671 Note: Figures are rounded to the nearest ton and may not sum to exact totals shown due to rounding. 28 Ocean-going vessel emission estimates are sourced from the 2010 National Marine Emissions Inventory associated with Region 2, the area within the marine inventory that corresponds to waters within the port's jurisdiction. SNC-Lavalin, 2010 National Marine Emissions Inventory for Canada, March 31, 2012 (not yet published; available by request from Environment Canada). 29 Cargo-handling equipment, rail locomotives, and trucks and terminal eet vehicle estimates are sourced from the 2010 Landside Emissions Inventory. SNC-Lavalin, Port Metro Vancouver 2010 Landside Emissions Inventory, March 26, 2012, www.portmetrovancouver.com/en/environment/initiatives/air.aspx, last accessed October 2013. Northwest Ports Clean Air Strategy Update 2013 37 only) Continued > United States 1% sulfur or equivalent 0.1% sulfur or equivalent 30 13, 2010, APPENDIX B. AIR EMISSION REGULATIONS IN U.S. AND CANADA summarizes the relevant emission-related regulations in the United States and Canada for the various sectors of port- Phase I: After August 1, 2012 Phase II: January 1, 2015 2001 Tier 1 engine standards also applied to some 19902000 engines upon remanufacture implemented (NO X standard is equivalent to the amendments adapted by the NO X International Convention for the Prevention of Pollution from Ships (MARPOL) Annex VI in 2008. 2011 Tier 2 engine standards phased in 2016 Tier 3 engine standards phased in Table B-1. Comparison of Air Emission Regulations in the United States and Canada X Canada 1% sulfur or equivalent 0.1% sulfur or equivalent lename=723.pdf, last accessed October 2013. After August 1, 2012 related vessels, equipment, and vehicles. Ocean-Going Vessels (Marine Class C3) After January 1, 2015 Aligned with IMO MARPOL Annex VI requirements for NO Fuel Standards inside ECA (200 Regulated item Table B-1 nautical miles from shore) Engine Standards for Category 3 Engines Displacement (D) 30 liters per International Maritime Organization, "Information on North American Emission Control Area (ECA) under MARPOL Annex VI," May cylinder 30 www.imo.org/blast/blastDataHelper.asp?data_id=29099& Northwest Ports Clean Air Strategy Update 2013 38 Continued > 32 32 ed, engine upgrade United States 15 ppm sulfur (the sulfur limits are not applicable only) (continued) After June 2007 < 500 ppm sulfur After June 2012 to residual fuels) 2004: Tier 1 engine standards apply (NO X 20042007: Tier 2 engine standards phased in 20092014 :Tier 3 engine standards phased in 20142017: Tier 4 engine standards for engines > 600 kW phase-in 2008: Requirements to install available, certi kits for engines 1973last Tier 2 model year and > 600 kW were implemented Table B-1. Comparison of Air Emission Regulations in the United States and Canada 15 ppm sulfur (the sulfur limits are not applicable Canada After June 2007 < 500 parts per million (ppm) sulfur 37 kilowatts. Engines < 37 kilowatts are subject to non-road standards. After June 2012 to residual fuels for sale for small and medium-sized vessels) New engines purchased on or after January 1, 2016, emission Harbor Vessels (Marine Class C2 and smaller) standards are aligned with U.S. EPA for Category 2 (displacement between 5 and 30 liters per cylinder) marine diesel engines (includes Tier 3 and Tier 4). Does not include EPA requirements for remanufacturing. No additional domestic standards in Canada for small marine diesel engines (Category 1, displacement under 7 liters per cylinder). Regulated item Fuel Standards Category 1 Marine Engines (Displacement < 57 liters per cylinder*) Category 2 Marine 31 Engines (57 liters Displacement per cylinder < 30 liters ) Category 1 and Category 2 engines typically range from 500kW8000 kW. In the United States, the threshold is 5 liters per cylinder; in Canada, 7 liters is the threshold. 31 Tier 1 and Tier 2 standards only apply to engines 32 Northwest Ports Clean Air Strategy Update 2013 39 0.1 Continued > United States 15 ppm sulfur phased in 0.01 gram/bhp-hour 0.2 gram/bhp-hour standard (continued) 500 ppm sulfur 15 ppm sulfur U.S. EPA compression-ignition engine standards: 19962002: Tier 1 engine standards are phased in 20012006: Tier 2 engine standards are phased in 20062010: Tier 3 engine standards are phased in 20112013: Tier 4i engine standards are phased in 2014: Tier 4 engine standards are phased in www.epa.gov/otaq/standards/nonroad/nonroadci.htm 20062010: New heavy-duty vehicle (HDV) engine PM standards gram/bhp-hour New HDV engine PM standards New HDV engine NO X New regulation requires HDV engine manufacturers to ciency and reduce GHG emissions improve ef 2007: 2010: 2004: 2007: 2010: 2014: Table B-1. Comparison of Air Emission Regulations in the United States and Canada Emission standards aligned with U.S. EPA compression-ignition 0.1 19962002: Tier 1 engine standards are phased in 20012006: Tier 2 engine standards are phased in 20062010: Tier 3 engine standards are phased in www.ec.gc.ca/lcpe-cepa/eng/regulations/ detailReg.cfm?intReg=88 0.01 gram/bhp-hour 20122014: Tier 4i engine standards are phased in 0.2 gram/bhp-hour Canada standard 500 ppm sulfur 15 ppm sulfur phased in ciency and reduce GHG emissions 2007: 2010: 15 ppm sulfur engine standards: 2014: Tier 4 engine standards are phased in Not aligned with EPA for spark-ignition engines 20062007: Engine emission standards aligned with U.S. EPA for air pollutants 2004: New heavy-duty vehicle (HDV) engine PM standards gram/bhp-hour 2007: New HDV engine PM standards 2010: New HDV engine NO X New regulation requires HDV engine manufacturers to 2014: improve ef www.ec.gc.ca/lcpe-cepa/eng/regulations/detailreg.cfm?intReg=214 75kW560 kw (typical range of CHE) Cargo-Handling Equipment (non-road) Trucks (on-road) Fuel Standards Engine Standards Regulated item Fuel Standards Engine Standards Northwest Ports Clean Air Strategy Update 2013 40 ed, upgrade kits United States 500 ppm sulfur 15 ppm sulfur ned by the 2008 Inland Marine and (continued) June 2007: June 2012: 2000: Tier 0 engine standards for all new and remanufactured locomotives 19732001 2000: Tier 1 engine standards for all new and remanufactured locomotives 20022004 2000: Tier 2 engine standards for all new and remanufactured locomotives 2005 and newer 2008 New Tier 0 engine standards required for all new and remanufactured 19731992 line-haul locomotives and 19732001 switch locomotives engines 2008 New Tier 1 engine standards required for all new and remanufactured 19932004 line-haul locomotives and 20022004 switcher locomotives 2008 New Tier 2 engine standards required for all new and remanufactured 20052011 line-haul locomotives and 20052010 switcher locomotives 2008: Requirements to install available, certi on remanufactured engines 1973last Tier 2 model year are implemented 2012: Tier 3 engine standards for all new locomotives and for remanufactured 20122014 line haul locomotives and 20112014 switcher locomotives 2015: Tier 4 engine standards for all new engines and for remanufactured 2015 locomotives Table B-1. Comparison of Air Emission Regulations in the United States and Canada Canada 500 ppm sulfur 15 ppm sulfur 500 ppm sulfur is allowed for sales Transport Canada is developing new emissions regulations under the Railway Safety Act that will align with U.S. EPA regulations, but there is currently no implementation date for these regulations. June 2007: June 2012: June 2014: 33 Regulated item Locomotives (rail) Fuel Standards Engine Standards rst engine standards went into effect in 2000 based on the 1997 locomotive rule. Tier 0Tier 2 engine standards were strengthe The 33 Locomotive rule. Northwest Ports Clean Air Strategy Update 2013 41 APPENDIX C. SUMMARY OF PUBLIC COMMENTS In June 2013, the partners released a draft of this Strategy Update for public review and comment. Outreach was conducted, and public open houses were held to solicit comments. Comments were accepted at the open houses, in person, by mail, and online. The ports of Seattle and Tacoma conducted a public comment period from June 11 through July 31, 2013. Port Metro Vancouver posted the draft Strategy Update for public comment on June 21 and accepted comments through August 9. The three ports received comments from 45 respondents; these comments are summarized below. The partners reviewed all comments received and revised the Strategy Update. Positive support of the Strategy Update and goals and focus on pilot studies, demonstration projects, and performance reporting. Need mandatory approach (vs. current focus on voluntary), and as an extension, more specic targets (e.g., not just having a fuel management program, but dening criteria that program must meet). Many stated that while a voluntary approach is good, success depends on the contributor. Expand scope (e.g., fugitive emissions, noise). Ensure absolute emission reductions, not just intensity-based emission reductions. Capture large emission sources, such as ocean-going vessels during transit and maneuvering. Improve communications and collaboration with public/other agencies to help achieve Strategy objectives. Available funding will not be sufcient to fulll the long-term emission-reduction goals. Customers need nancial support to meet targets (e.g., inability to afford the price and maintenance of a 2007 or newer truck with the current economy and status of the drayage business). Conicting feedback on truck program depending on the contributor (too stringent and wrong focus vs. not stringent or fast enough). Desire for new trucks to replace old trucks to increase work potential and regional air quality. Suggestions to consider: vessel speed reduction initiative, vessel energy efciency, and alternative fuel use incentives. Should have more focus on alternative fuels, such as natural gas and hydrogen fuel cells. Northwest Ports Clean Air Strategy Update 2013 42
Limitations of Translatable Documents
PDF files are created with text and images are placed at an exact position on a page of a fixed size.
Web pages are fluid in nature, and the exact positioning of PDF text creates presentation problems.
PDFs that are full page graphics, or scanned pages are generally unable to be made accessible, In these cases, viewing whatever plain text could be extracted is the only alternative.